IK Multimedia
-
-
IK Multimedia UNO Synth Pro X
Sound generation
3 discrete wave-morphing oscillators
3 super-fast envelopes with loop and retrigger options
PWM, sync, FM and ring modulation
Dual-filter design, OTA and SSI-chip based
12 studio-quality FX in 3 slots + analogue drive
Performance tools
Advanced paraphonic 64-step sequencer
10-mode arpeggiator with pattern designer
New Bassline mode plus legato, mono, paraphonic
Audio input to filters and FXs or pass-through
Complete controls
Over 30 hands-on controls
16-slot modulation matrix
256 user-editable presets
USB / MIDI / CV / Gate in/out
Backlight control and onboard factory preset restore
Advanced software control for Mac/PC
Ready for travel
Ultralight and ultraportable
PSU or USB battery pack power supply
Balanced stereo and headphone outputs
Editor/Librarian included
Optional gig bag available
Dimensions
Size (W x D x H): 33.3 x 15 x 5 cm
Enclosure: Plastic
Weight: 800 g
Power: iRig PSU-3A (included) or USB (5V/1.5A, 7.5W or above)
Package includes
UNO Synth PRO X
1x USB-C to USB-C Cable – 60 cm
Power Supply Unit
Quick start guide
Registration card€609,00€670,00IK Multimedia UNO Synth Pro X
€609,00€670,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iRig Stream Mic Pro
Common
Interface type: 2 in/2 out or 4 in/2 out
Conversion: 24-bit A/D, 24-bit D/A
Sampling rate: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Power: USB bus powered. When connected to an external PSU (iRig PSU 3A, not included), iRig Stream Mic Pro charges the connected iOS lightning device.
Device connection: mini-DIN
Dimensions: 55 mm x 136 mm x 38 mm
Weight: 430 g
Microphone
Microphone type: condenser, electret
Capsules: dual 0.55″ gold-sputtered
Polar patterns: cardioid, omni, figure-8, stereo
Frequency response: from 20 Hz to 20 kHz
Maximum sound pressure: 115 dB SPL
High-pass filter: selectable between 60, 100 and 200 Hz
Headphone Output
Connector: 1/8″ (3.5mm) TRS jack
Frequency response: from 20 Hz to 20 kHz
Output level: 7 mW/channel (32 Ohm load)
Dynamic range: 87 dB(A)
Aux Input
Connector: 1/8″ (3.5 mm) TRS jack
Nominal input level: -10 dBV
Frequency response: from 10 Hz to 20 kHz
Package includes
iRig Stream Mic Pro
Table stand
mini-DIN to iOS Lightning cable – 60 cm
mini-DIN to USB-C cable – 150 cm
5/8″ to 1/4″ thread adapter€172,00€191,00IK Multimedia iRig Stream Mic Pro
€172,00€191,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLoud Precision 6 Black
6.5″ ultralight coated paper mid-woofer
1.5″ high output, low distortion chambered textile dome tweeter
Audiophile, custom-designed Class-D power amplifiers
150 W total RMS power
Max SPL, peak, pair, music, 1 m: 116 dB
Complete DSP controlled system, 96 kHz sampling rate
45 Hz to 30 kHz frequency response +/- 1 dB
37 Hz low frequency extension @-4 dB
Phase response: Coherent, 0/+20° max from 150 Hz up
Phase rotation at 100Hz (with high pass filter off): 45° max
Directivity (Vertical – all voices): +/-50°
Directivity (Vertical – Wide Dispersion mode): +65°/-50°
Continuous, long term SPL free field, 1 m distance, one speaker, fullband pink noise: 100 dB(A)
Peak SPL free field, 1 m distance, one speaker, fullband pink noise: 106 dB(A)
Peak SPL, half space, 1 m distance, one speaker, fullband pink noise: 108 dB(A)
Maximum peak SPL, per pair, 1 m distance, music program: 116 dB(A)
Crossover frequency: 1.9 kHz
Crossover type: 8th order, linear phase
LF Power amp (short term): 120 W
HF Power amp (short term): 30 W
Power amps distortion at nominal power: 0.005%
Total latency or TOF: 2.5 ms
Adjustable additional delay: 0-10 ms
High pass filter: off, 35, 50, 65, 80 Hz
LF contour: from -10 to +6 dB
Desk contour: from -10 to 0 dB
Mid contour: from -4 to +4 dB
HF contour: from -6 to +6 dB
Sentitivity: -4 dBu / 90 dBSPL
Input gain trim: +/-5 dB
Unit to unit consistency: +/-0.5 dB
Operating temperature (non condensing): from 0 to 35 °C
Coherent time response across the audio spectrum
High performance vented design
Built-in ARC room calibration
X-MONITOR technology
Remote control for X-MONITOR voice selection and measurement process control
X-MONITOR macOS and Windows control software
Handcrafted in Italy
Dimension and weight
(H x W x D): 353 mm/13.89″ x 201 mm/7.91″ x 282 mm/11.10″
7.7 kg/17 lbs.
Package includes
1 x iLoud Precision 6 monitor
Power cord
ARC Microphone
ARC Microphone clamp
USB-B to USB-A 2.5 m/8.2 ft. cable
1 x kit of 4 iLoud Isolation Pods€999,00€1.099,00IK Multimedia iLoud Precision 6 Black
€999,00€1.099,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLoud Precision 5
5″ ultralight coated paper mid-woofer
1.5″ high output, low distortion chambered textile dome tweeter
Audiophile, custom-designed Class-D power amplifiers
135 W total RMS power
Max SPL, peak, pair, music, 1 m: 114.5 dBA
Complete DSP controlled system, 96 kHz sampling rate
46 Hz to 30 kHz frequency response +/- 1 dB
39 Hz low frequency extension @-4 dB
Phase response: Coherent, 0/+20° max from 150 Hz up
Phase rotation at 100Hz (with high pass filter off): 50° max
Directivity (Vertical – all voices): +/-50°
Directivity (Vertical – Wide Dispersion mode): +70°/-50°
Continuous, long term SPL free field, 1 m distance, one speaker, fullband pink noise: 98.5 dB(A)
Peak SPL free field, 1 m distance, one speaker, fullband pink noise: 104.5 dB(A)
Peak SPL, half space, 1 m distance, one speaker, fullband pink noise: 106.5 dB(A)
Maximum peak SPL, per pair, 1 m distance, music program: 114.5 dB(A)
Crossover frequency: 2.1 kHz
Crossover type: 8th order, linear phase
LF Power amp (short term): 110 W
HF Power amp (short term): 25 W
Power amps distortion at nominal power: 0.005%
Total latency or TOF: 2.5 ms
Adjustable additional delay: 0-10 ms
High pass filter: off, 35, 50, 65, 80 Hz
LF contour: from -10 to +6 dB
Desk contour: from -10 to 0 dB
Mid contour: from -4 to +4 dB
HF contour: from -6 to +6 dB
Sentitivity: -4 dBu / 88 dBSPL
Input gain trim: +/-5 dB
Unit to unit consistency: +/-0.5 dB
Operating temperature (non condensing): from 0 to 35 °C
Coherent time response across the audio spectrum
High performance vented design
Built-in ARC room calibration
X-MONITOR technology
Remote control for X-MONITOR voice selection and measurement process control
X-MONITOR macOS and Windows control software
Handcrafted in Italy
Dimension and weight
(H x W x D): 296 mm/11.65″ x 177 mm/6.96″ x 223 mm/9.17″
6.1 kg/13.4 lbs.
Package includes
1 x iLoud Precision 5 monitor
Power cord
ARC Microphone
ARC Microphone clamp
USB-B to USB-A 2.5 m/8.2 ft. cable
1 x kit of 4 iLoud Isolation Pods€969,00€1.066,00IK Multimedia iLoud Precision 5
€969,00€1.066,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia TONEX Capture
IK Multimedia’s TONEX Capture is a cutting-edge Tone Model builder, allowing you to effortlessly create a digital profile of any amplifier or pedal’s true-to-life tone! By rigging up the TONEX Capture to your amp and audio interface, you can easily create an IK Multimedia digital Tone Model that replicates every nuance of your amplifier and cab’s (or pedal’s) response, providing you with a software emulation that Sweetwater guitarists find is virtually indistinguishable from the real thing. In addition, the TONEX Capture also doubles as a re-amp box — an essential tool for guitarists and producers looking to audition their direct tracks through a multitude of real-world guitar amps. If you’re looking to dive headfirst into the advanced modelling world of IK Multimedia’s robust TONEX ecosystem, there’s no simpler way to do it than with the TONEX Capture.€218,00€240,00IK Multimedia TONEX Capture
€218,00€240,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iRig Pro Quattro I/O Deluxe
Microphone Inputs 1-2
2 x balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
Input impedance: 1 kOhms
Input level, min gain: 0 dBFS is obtained with a -1.5 dBu signal at the XLR input
Input level, max gain: 0 dBFS is obtained with a -55 dBu signal at the XLR input
Frequency response: from 10 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic Range: 103 dB(A), min gain
Phantom power: 48V / -4V
Built-in microphone
Type: MEMS
Polar pattern: omnidirectional
Frequency response: from 30 Hz to 20 kHz
Max SPL: 110 dBSPL
Sensitivity: -41.5 dB (1 kHz, 94dB SPL)
Instrument Inputs 1-2
2 x unbalanced, Hi-Z, TS 1/4” Jack, Tip: signal / Shield: ground
Input impedance: 1 MOhms
Input level, min gain: 0 dBFS is obtained with a +10 dBu signal at the TS input
Input level, max gain: 0 dBFS is obtained with a -43 dBu signal at the TS input
Frequency response: from 7 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic range: 103 dB(A), min gain
Microphone Inputs 3-4
2 x balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
Input impedance: 1 kOhms
Input level, min gain: 0 dBFS is obtained with a -3 dBu signal at the XLR input
Input level, max gain: 0 dBFS is obtained with a -54 dBu signal at the XLR input
Frequency response: from 10 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic range: 101 dB(A), min gain
Phantom power: 48V / -4V
Line Inputs 3-4 (balanced)
2 x balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
Input impedance: 1 kOhms
Input level, min gain: 0 dBFS is obtained with a -3 dBu signal at the XLR input
Input level, max gain: 0 dBFS is obtained with a -54 dBu signal at the XLR input
Frequency response: from 10 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic range: 101 dB(A), min gain
Phantom power: 48V / -4V
Line Inputs 3-4 (unbalanced)
Unbalanced, TRS 3.5 mm stereo Jack and RCA
Input impedance: 2.1 kOhms
Nominal input level: -3.5 dBV (-10 dBV with 6.5 dB of headroom)
Frequency response: from 16 Hz to 46 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 93 dB(A)
Line Outputs (balanced)
2 x balanced, 3-pin XLR, Pin 2: hot / Pin 3: cold / Pin 1: ground
Floating balanced outputs with automatic level compensation when working in unbalanced mode
Output impedance: 150 Ohms balanced
Output level: 0 dBFS corresponds to +12 dBu
Frequency response: from 5 Hz to 44 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 100 dB(A)
Channels crosstalk: 88 dB(A)
Stereo Output (unbalanced)
Unbalanced, TRS 3.5 mm stereo jack
Output impedance: 150 Ohms balanced
Output level: 0 dBFS corresponds to +12 dBu
Frequency response: from 5 Hz to 44 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 100 dB(A)
Channels crosstalk: 88 dB(A)
Headphones Output
TRS 3.5 mm stereo jack
Output impedance: 22 Ohm
Output level: 26 mW/channel (32 Ohm load)
Frequency response: from 15 Hz to 44 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 100 dB(A)
Common
AD and DA Resolution: 24-bit
Sampling Rate: 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz
Power: USB bus power, battery power (4 x AA), DC power supply (9VDC) or external USB power supply (5VDC, 1A min)
Device Connection: Mini-DIN
Size: 166 mm / 6.54″ x 92 mm / 3.62″ x 43 mm / 1.69″
Weight: 325 g / 0.72 lb (batteries excluded)
Battery Life:• Recording – Max load*: 1 hour, 30 minutes (Alkaline); 3 hours (NiMH rechargeable)• Playback – Min load**: 2 hours, 30 minutes (Alkaline); 4 hours (NiMH rechargeable)
*Max load condition: four inputs connected each to a 1.6mA phantom-powered load, input gains set to maximum, 32 Ohm headphones connected.**Min load condition is as follows: music playing, phantom power OFF, 32 Ohm headphones connected.
Dimensions
Size: 166 mm x 92 mm x 43 mm
Weight: 325 g (batteries excluded)
Package includes
iRig Pro Quattro I/O interface
1/4″ thread adapter
Lightning to Mini-DIN connection cable (60cm/23.62″)
USB-C to Mini-DIN connection cable (60cm/23.62″)
USB-A to Mini-DIN connection cable (60cm/23.62″)
1x 2.5mm TRS male to MIDI female adapter (10cm/3.9″)
4 x 1.5V AA Battery
2 x iRig Mic XY
Windshield
Power Supply Unit
Carrying case€439,00€483,00IK Multimedia iRig Pro Quattro I/O Deluxe
€439,00€483,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iRig Pro Quattro I/O
Microphone Inputs 1-2
2 x balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
Input impedance: 1 kOhms
Input level, min gain: 0 dBFS is obtained with a -1.5 dBu signal at the XLR input
Input level, max gain: 0 dBFS is obtained with a -55 dBu signal at the XLR input
Frequency response: from 10 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic Range: 103 dB(A), min gain
Phantom power: 48V / -4V
Built-in microphone
Type: MEMS
Polar pattern: omnidirectional
Frequency response: from 30 Hz to 20 kHz
Max SPL: 110 dBSPL
Sensitivity: -41.5 dB (1 kHz, 94dB SPL)
Instrument Inputs 1-2
2 x unbalanced, Hi-Z, TS 1/4” Jack, Tip: signal / Shield: ground
Input impedance: 1 MOhms
Input level, min gain: 0 dBFS is obtained with a +10 dBu signal at the TS input
Input level, max gain: 0 dBFS is obtained with a -43 dBu signal at the TS input
Frequency response: from 7 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic range: 103 dB(A), min gain
Microphone Inputs 3-4
2 x balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
Input impedance: 1 kOhms
Input level, min gain: 0 dBFS is obtained with a -3 dBu signal at the XLR input
Input level, max gain: 0 dBFS is obtained with a -54 dBu signal at the XLR input
Frequency response: from 10 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic range: 101 dB(A), min gain
Phantom power: 48V / -4V
Line Inputs 3-4 (balanced)
2 x balanced, XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
Input impedance: 1 kOhms
Input level, min gain: 0 dBFS is obtained with a -3 dBu signal at the XLR input
Input level, max gain: 0 dBFS is obtained with a -54 dBu signal at the XLR input
Frequency response: from 10 Hz to 46 kHz within 3 dB (96 kHz sample rate), min gain
Dynamic range: 101 dB(A), min gain
Phantom power: 48V / -4V
Line Inputs 3-4 (unbalanced)
Unbalanced, TRS 3.5 mm stereo Jack and RCA
Input impedance: 2.1 kOhms
Nominal input level: -3.5 dBV (-10 dBV with 6.5 dB of headroom)
Frequency response: from 16 Hz to 46 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 93 dB(A)
Line Outputs (balanced)
2 x balanced, 3-pin XLR, Pin 2: hot / Pin 3: cold / Pin 1: ground
Floating balanced outputs with automatic level compensation when working in unbalanced mode
Output impedance: 150 Ohms balanced
Output level: 0 dBFS corresponds to +12 dBu
Frequency response: from 5 Hz to 44 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 100 dB(A)
Channels crosstalk: 88 dB(A)
Stereo Output (unbalanced)
Unbalanced, TRS 3.5 mm stereo jack
Output impedance: 150 Ohms balanced
Output level: 0 dBFS corresponds to +12 dBu
Frequency response: from 5 Hz to 44 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 100 dB(A)
Channels crosstalk: 88 dB(A)
Headphones Output
TRS 3.5 mm stereo jack
Output impedance: 22 Ohm
Output level: 26 mW/channel (32 Ohm load)
Frequency response: from 15 Hz to 44 kHz within 3 dB (96 kHz sample rate)
Dynamic range: 100 dB(A)
Common
AD and DA Resolution: 24-bit
Sampling Rate: 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz
Power: USB bus power, battery power (4 x AA), DC power supply (9VDC) or external USB power supply (5VDC, 1A min)
Device Connection: Mini-DIN
Size: 166 mm / 6.54″ x 92 mm / 3.62″ x 43 mm / 1.69″
Weight: 325 g / 0.72 lb (batteries excluded)
Battery Life:• Recording – Max load*: 1 hour, 30 minutes (Alkaline); 3 hours (NiMH rechargeable)• Playback – Min load**: 2 hours, 30 minutes (Alkaline); 4 hours (NiMH rechargeable)
*Max load condition: four inputs connected each to a 1.6mA phantom-powered load, input gains set to maximum, 32 Ohm headphones connected.**Min load condition is as follows: music playing, phantom power OFF, 32 Ohm headphones connected.
Dimensions
Size: 166 mm x 92 mm x 43 mm
Weight: 325 g (batteries excluded)
Package includes
iRig Pro Quattro I/O interface
1/4″ thread adapter
Lightning to Mini-DIN connection cable (60cm/23.62″)
USB-C to Mini-DIN connection cable (60cm/23.62″)
USB-A to Mini-DIN connection cable (60cm/23.62″)
1x 2.5mm TRS male to MIDI female adapter (10cm/3.9″)
4 x 1.5V AA Battery€399,00€439,00IK Multimedia iRig Pro Quattro I/O
€399,00€439,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia USB-C to Micro-USB
Use this IK Multimedia USB Type-C to Micro-USB Cable with select iRig and UNO products. With a USB Type-C Port at one end, and a micro-USB port at the other, the cable is 1.50m long.€36,00€40,00IK Multimedia USB-C to Micro-USB
€36,00€40,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLine Stereo Aux
24k gold-plated connectors for maximum connectivity
High-purity copper conductors for optimal signal transfers
Low-capacitance insulation to preserve transients
High-density shielding to guard against electromagnetic interference (EMI)
Compatible with smartphones, tablets, laptops, desktops and most high-end audio equipment
Made in Italy
Limited lifetime warranty€24,40€26,80IK Multimedia iLine Stereo Aux
€24,40€26,80Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLine RCA Output
24k gold-plated connectors for maximum connectivity
High-purity copper conductors for optimal signal transfers
Low-capacitance insulation to preserve transients
High-density shielding to guard against electromagnetic interference (EMI)€30,50€33,60IK Multimedia iLine RCA Output
€30,50€33,60Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLine Mono Output
24-karat gold-plated connectors for optimal connectivity
High-purity copper conductors for stellar signal transfers
Low-capacitance insulation to preserve transients
High-density shielding guards against electromagnetic interference (EMI)
Compatible with smartphones, tablets, laptops, desktops, and nearly all high-end audio equipment€24,40€26,80IK Multimedia iLine Mono Output
€24,40€26,80Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia Mobile Music
24K gold-plated connectors for maximum connectivity in all environments
High-purity copper conductors for the best-quality signal transfer
Low-capacitance insulation to preserve transients
High-density shielding to guard against EMI
Carrying case included
Made in Italy
Compatible with smartphones, tablets, laptops, desktops and most high-end audio equipment
Cables can be purchased individually€73,20€80,50IK Multimedia Mobile Music
€73,20€80,50Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLine Input / Output Extension
Straight – straight
Length: 0.60 m
Type of audio connector: Jack 3.5 mm TRRS
1 x jack 3.5 mm TRS male, 1 x jack 3.5 mm TRS female€24,40€26,80IK Multimedia iLine Input / Output Extension
€24,40€26,80Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLine Headphone Stereo Splitter
24k Gold-Plated Connectors
High-Purity Copper Conductors
Low-Capacitance Insulation
High-Density Shielding€18,30€20,10IK Multimedia iLine Headphone Stereo Splitter
€18,30€20,10Διαθέσιμο σε 1-3 ημέρες
-
-
€399,00
€439,00IK Multimedia AXE I/O + AmpliTube 5 MAX Bundle
€399,00€439,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iLoud MTM
Type: 2-Way/3-speakers bi-amped, digitally controlled studio monitor
LF Drivers: 2 x 3.5″ polypropylene custom made mid-woofers
HF Driver: 1″ low distortion, back chambered silk dome tweeter
Acoustic Design: DSP tuned bass reflex
Number of amps per speaker: 2
Amplifiers type: High efficiency Class-D
Total power: 100W RMS
LF power: 70W RMS
HF power: 30W RMS
Crossover Type: Linear Phase Variable Order
Crossover Frequency: 3.1kHz
Frequency response: from 50 Hz to 24 kHz +/- 2dB (40 Hz -6dB when uncal, -3 dB when cal)
Phase response: System remains coherent within +/- 15° from 200Hz to 20kHz
Sensitivity at +4dBu: 0dBu signal generates a 100 dB SPL @ 1 m
Sensitivity at -10dBV: -11dBu signal generates a 100 dB SPL @ 1 m
Maximum SPL @ 1m, one speaker playing, on axis: 103dB from 200Hz up sine wave, 95dB at 100Hz sine, 93dB pink noise
Placement setup: Manual switches for LF Extension, LF trim, HF trim, Desk position
LF extension: switch Sets -3dB point of the frequency response at 40, 50 or 60 Hz
LF switch: Low shelf, +2dB or -3dB from 100Hz down
HF switch: high shelf, +2dB or -2dB from 8kHz up
Desk switch: -4dB at 160Hz and +1dB at 1.8kHz
Calibration: Fully automatic and built-in digital calibration, microphone included
Measurement Microphone: Omnidirectional, Mems based precision measurement microphone
Full DSP control
Connectors: 1x combo XLR-1/4? TRS balanced input; 1/8? TS ARC microphone input, 1 x USB type-B (service use only), AC POWER socket
Power requirement: 90 to 240 V AC, auto-ranging, 50 or 60Hz, 120W max power consumption€345,00€380,00IK Multimedia iLoud MTM
€345,00€380,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iKlip 3 Video
Βάση για την στήριξη Tablet & iPad σε τρίποδα και βάσεις μικροφώνων€75,00€83,00IK Multimedia iKlip 3 Video
€75,00€83,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iKlip 3 Deluxe
Περιέχει τις βάσεις για Tablet iKlip 3 & iKlip 3 Video.€99,00€109,00IK Multimedia iKlip 3 Deluxe
€99,00€109,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia PSU-3A
Power supply unit for iRig Pro I/O, iRig Keys I/O, iRig Stomp I/O€48,00€53,00IK Multimedia PSU-3A
€48,00€53,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iKlip GO
Ultra-compact
Includes integrated/detachable Bluetooth shutter controller
Ball-joint attachment allows for 90° angle and 360° rotation
6.5/16,6cm extends up to 29.1″/74cm
Expandable grip from 2.13″/54mm up to 3.58″/91mm
Standard UNC 1/4″-20 threaded ball mount
Works with smartphones with screens from 3.5″ to 6″ with case on
Works with compact digital cameras and small video cameras like GoPro
Works with handheld audio field recorders
Designed in Italy
iKlip GO comes with free apps from IK Multimedia and works with many other apps.
Holds any iPhone and smartphone model with screens ranging in size from 3.5″ to 6″ with case on
Works with compact digital cameras, small video cameras, field recorders and devices compatible with standard UNC 1/4″-20 thread
Standard UNC 1/4″-20 threaded ball mount
360° rotation and 90° adjustable holder angle
Includes integrated/detachable Bluetooth shutter controller
Material: Thermoplastic / Aluminum
Maximum weight applicable: 1kg / 2.2lb€39,90€44,00IK Multimedia iKlip GO
€39,90€44,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iKlip Grip Pro
Holds any iPhone and smartphone model with screens ranging in size from 3.5″ to 6″ with case on
Works with DSLR and Digital Cameras, Field Recorders and devices compatible with standard UNC 1/4″-20 thread
Standard UNC 1/4″-20 threaded ball mount
360° rotation and 90° adjustable holder angle
Includes integrated/detachable Bluetooth shutter controller
Material: Thermoplastic / Aluminum
Maximum weight applicable: 1kg
Package includes
iKlip Grip Pro bracket
iKlip Grip Pro handle / tripod / extender
Remote Bluetooth shutter
Lanyard
Dimensions
Holding bracket width: 54mm (min) – 91mm (max)
Height: 19cm when folded (without holding bracket)
Extends up to 62cm
Weight: 200gr€75,00€83,00IK Multimedia iKlip Grip Pro
€75,00€83,00Διαθέσιμο σε 1-3 ημέρες
-
IK Multimedia iKlip A/V
Δέχεται οποιοδήποτε κινητό ή tablet από 3.5 έως 6.0 ίντσες
Θόρυβος: -98 fullband dB, με ενεργοποιημένο phantom
Μέγιστη στάθμη εξόδου: 2 Vrms
Παραμόρφωση: 0.025% THD
Μέγιστο ρεύμα phantom: 6mA
διάρκεια μπαταρίας (Αλκαλικές ΑΑ): περίπου 60 ώρες, όταν το phantom είναι ενεργοποιημένο και περίπου 20 ώρες όταν το phantom είναι απενεργοποιημένο
Υλικό: Θερμοπλαστικό / Αλουμίνιο
Το πακέτο περιλαμβάνει:
1 x iKlip A / V
1 x Καλώδιο TRrS 1/8
Βραχίωνας κινητού
Διαστάσεις:
Βάρος: 353 gr
54 mm X 91 mm X 3.58 mm€172,00€189,00IK Multimedia iKlip A/V
€172,00€189,00Διαθέσιμο σε 1-3 ημέρες
For pro studios, whether digital or analogue console-based, ARC Studio allows for correction and custom-tuning for any setup while the inherent system’s sonic quality.
For DAW-based studios, ARC Studio frees you from the hassle of inserting plug-ins on the master bus of your work and preserves zero-latency monitoring setups.
You can customize your setup for ideal performance no matter your preference, with adjustable upper and lower correction limits, variable resolution and smoothing, and both natural and linear phase modes.